V1 Jeffrey's City Goblin SS Turbo Illusion Purple

[redline]

Not sure if you got this mounted but here is some pictures of when I did mine, around post 35 http://dfkitcar.com/forum/index.php...blin-09-ss-turbo-titled-registered.420/page-2

And if you zoom in on the pic on post 43 you can see the adapter for the master cylinder, you're missing 1 part in that mount kit that I can see

That is all I got in my kit and it went together just fine? What do you think is missing?

 

[Dre]

I noticed that when I go to autozones website and look up the rotors included in the kit, it says that it's not compatible with my car. Does that mean these wont work with the donor hardware?

 

[redline]

No, it should all work just fine.

 

[Briann1177]

DF needs to work on getting the Goblin into the big box computers. That way if I ever need a new radiator hose, caliper or whatever, they can pull the list right up.

 

[Jlarson524]

Does anyone have or are there any pictures on how to attach the seat brackets that come with the kit to attach the Corbeau seats?

 

[IDRVSLO]

Im sure someone will have a better picture.

 

[Jlarson524]

Torque value?

 

[Lonny]

33 ft lbs
The aluminum plate goes under the frame.

 

[ctuinstra]

Torque value?

You made the same mistake many have, including us, the aluminum should be on the bottom, not the top. I'll see if I can find the torque specs.

 

[Briann1177]

That's about the only torque value I couldn't find too. I just tightened mine down until I thought the felt tight enough. Probably about 40 lb-ft or so. They haven't fallen off yet after 2000
miles.

 

[Subie_zack]

hey so i'm jeff's roommate and i'm helping him with putting this thing to together cause he been slacking lol. but does anyone have pictures of the clutch line going from the master cylinder going to the slave cylinder . i don't want us to continue on then find out we gotta back track because he didn't put the line in sooner. but here the progress we made on the rear suspension tonight. its going to be torque all down tomorrow and make sure we set the coil over up properly. btw yes that is a kangaroo his name is randy and he has a instagram @randyrogerroo

 

[ctuinstra]

The clutch line needs to go in the tunnel with the brake line. It should have been in there before the engine is mounted.

 

[Lonny]

You can work the clutch line in place but it is definitely easier before you install the engine.

You will need the tunnel cover off and the seats out of the way.

In the front the clutch line follows the same path as the bake line.

In the rear the clutch line goes between the subframe and the fuel tank and then up between the engine and fuel tank.

As you work it through the frame it will straighten some of the bends so once it is in place you will need to correct the bends. It is easy to do this with your hands.

This is also a good time to place the two heat exchanger tubes into the tunnel.

 

[Subie_zack]

Is it possible you can snap a picture of the master cylinder and the slave so we know what way to run the line.

 

[ctuinstra]

The short bends go to the front and the longer bends is in the rear. There should be a couple of short 90 degree bends in the front to follow the frame.

 

[Lonny]

The direction is correct in your image.

 

[Subie_zack]

So I’ve gotten it feed thru. But where do these 4 Mounting clips go or do they where every we feel like putting them?

 

[Subie_zack]

So I’ve gotten it feed thru. But where do these 4 Mounting clips go or do they where every we feel like putting them?View attachment 6432

Really just trying to figure how it goes back near the slave. up front is pretty simple and goes with the brake line.

 

[IDRVSLO]

Pull and bend it into place back there. Plenty of flex to it.

 

[Jlarson524]

Are these parts supposed to come with the kit? I’ve looked everywhere and don’t think I received them.